Front Seat Extreme / Stories

Nov 09, 2026 / BMW E36, Bohol, FSE Garage

Project E36: Building My BMW in Bohol

Original silver BMW E36 325i parked along a forest road in Bohol, Philippines

FSE STORIES / THE GARAGE / BOHOL, PHILIPPINES / ONGOING BUILD

This is the real build journal of my 1993 BMW E36 325i in the Philippines. Not a finished-car reveal, not a fictional race build, and definitely not a list of perfect upgrades. This is the actual journey: the work, the parts that didn't fit, conversations with the mechanic, the waiting, the lessons, and the little wins that make building an old BMW worth it.

The car is a silver four-door E36 with the M50B25 naturally aspirated inline-six and a manual gearbox. I want a naturally aspirated stroker eventually, built for the winding, scenic roads of Bohol. It's not the dedicated drift car; that's a separate project. This one is meant to look good, feel good, be reliable, stand out when it's parked, and come alive when I put my foot down. I'll do an occasional burnout, sure, but I am not building it for constant tire-burning abuse.

Silver E36 BMW photographed at shop in Bohol with lowered front stance
BUILD LOG // October 16 — Finally getting to see the E36 sitting lower. The stance was starting to come together.

01 / Before the upgrades: the real starting point

I started with an E36 that clearly had history. The exterior had potential: silver paint, dark windows, five-spoke wheels, an aggressive stance and a performance windshield banner. Inside, the car had a black interior and manual shifter. It was a cool car already, but mechanically there were issues hiding beneath that first impression.

Before its longer stay at the workshop, I had exhaust work welded up. I also began collecting and ordering parts rather than trying to do everything at once. With my job taking me away from Bohol, I needed someone local who could keep the build moving and send actual photos whenever something changed.

Actual silver BMW E36 project vehicle photographed from front in BoholSecond photograph showing exhaust work underneath the rear of the BMW E36
BUILD LOG // Early workshop view: a real look at the car and its front-end condition, before the detailed mechanical work.

02 / August–September: the parts start arriving

Late August and early September became a constant cycle of ordering, waiting, tracking shipments, bringing parts by the shop and coordinating around my travel schedule. I had an upgraded clutch kit, a clutch slave cylinder, suspension components, rear camber arms and bushings, cooling components, a water pump and pulley, belts, engine and transmission mounts, headlight controls and other smaller pieces on the way. I wanted to get the basic mechanical issues sorted before spending money chasing more power.

Amazon purchase-history screenshot showing BMW E36 restoration parts and arrival estimates
BUILD LOG // September 2026 — Parts on the way. Cooling components, suspension upgrades, and other replacement parts were arriving while I coordinated the build with Atan.

On September 2 I told Atan I was still in Bohol and would leave for Japan later that month. I wanted the parts delivered first and told him I was bringing more items by the shop. The radiator had already come out as the team got deeper into the cooling work.

Original M50 inline six engine bay after radiator removal during BMW E36 maintenance
BUILD LOG // September 2 — Atan: “We pull out the radiator boss.” Cooling-system work was underway.

03 / Suspension: setting it up for the roads here

The suspension work matters to me as much as the engine. Bohol has beautiful winding roads, but it also has rough pavement, dips and everyday traffic. My target is something low and planted without making the car frustrating to drive. That means the stance is only one part of the equation; I still want usable travel, tire clearance and sensible road manners.

Original close-up photo of silver E36 front wheel after first coilover ride height test
BUILD LOG // September 2 — Atan: “Boss we tested the front coilover left side heres the ride height.” First ride-height adjustment underway.

Along with the coilovers, I ordered rear suspension hardware including camber arms and bushings. Atan kept sending updates as the suspension work progressed.

Original rear spring and adjustable coilover damper on BMW E36 suspension
BUILD LOG // October 15 — Atan sent this update while working on the rear suspension. The coilover setup was starting to come together.
Actual mechanic crouched beside silver BMW E36 rear wheel during suspension setup
BUILD LOG // October 15 — Atan was checking the rear ride height and said he'd send another update once the jacks were removed.
Original BMW E36 underbody photo with red rear suspension control links being fitted
BUILD LOG // October 16 — Atan: “Now we install the control rods boss.” Another step forward with the rear suspension.

OCTOBER 16 / ATAN'S WORKSHOP UPDATE
After the control-rod photo I replied that the car must drive well now. Atan answered: “Yes boss good for drifting hehe.” His comment made me laugh, but my actual plan for this specific car is a strong naturally aspirated street build for Bohol's curves, not sustained drifting.

04 / September 5: inherited wiring and A/C surprises

The wiring turned out to be another story. I had installed a replacement headlight control, but the lighting still wasn't behaving as it should. The middle switch position wasn't bringing on the parking or marker lights, while the final position would activate the headlights. Pressing a fog-light button appeared to operate something that sounded like the headlight leveling motor.

BMW E36 dashboard rotary headlight control and fog light buttons original photograph
BUILD LOG // September 5 — The original headlight switch and vent. I sent Atan a detailed report of the strange lighting behavior, suspecting old electrical modifications needed to be traced.
Original BMW E36 rear fog light switch close-up from dashboard
BUILD LOG // September 5 — Close-up of the fog-light control. The buttons weren't responding normally; the electrical diagnosis remained unresolved at that stage.

Then there was the A/C. A previous owner had apparently bypassed the standard A/C switch and connected the system to a separate button. I could control the blower speed but not properly control the temperature through the normal panel. I told the shop I would rather identify the altered wiring, trace the grounds and fix the circuits properly than keep stacking new wires on top of unknown old work.

SEPTEMBER 5 / ATAN'S WORKSHOP UPDATE
I told Atan: “The fog light button doesn't work... I think previous owner mess with wiring.” Later I explained the A/C had been hard-wired to another switch and wanted the lighting and A/C controls investigated before adding more modifications.

05 / September 11–October 3: the clutch saga

This was one of the biggest detours in the entire build. I ordered an EFT Stage 3 performance clutch kit intended for the M50-equipped E36, with a rigid six-puck ceramic disc, pressure plate and release hardware. On paper it appeared to be the right choice. In the workshop, the pressure plate mounting pattern did not line up with the flywheel already in the car.

Original shop photo comparing smaller old and larger new clutch pressure plates on the ground
BUILD LOG // September 11 — Atan compared the old and new clutch pressure plates side by side, reporting that the replacement was bigger and couldn't be installed as presented.
Original E36 performance clutch disc kit laid next to existing components
BUILD LOG // September 11 — We compared the new clutch kit with the parts that came off the BMW. That's when the fitment headache started.

SEPTEMBER 11 / ATAN'S WORKSHOP UPDATE
Atan: “Cant be installed.” He clarified: “Holes for the bolts in the pressure plate cannot fit in the flywheel.” He proposed measuring the mounting holes after removing the flywheel. I wasn't comfortable drilling unverified holes just to force the parts together.

Original used pressure plate for BMW E36 photographed on white surface
BUILD LOG // September 11 — Atan checked the original pressure plate against the new one to figure out why the bolt holes weren't lining up.

The crucial detail came from the flywheel. The product listing noted that the clutch was intended for a factory dual-mass arrangement in some applications, but real parts and prior work can differ from what a listing suggests. The workshop confirmed a dual-mass flywheel was in the car and that it did not work with the pressure plate we had. I began looking at replacements and trying to establish exactly what combination would fit.

Original close-up of Getrag transmission case and casting stamp in E36
BUILD LOG // September 21 — I asked Atan for the transmission markings so I could double-check which clutch and flywheel setup we needed. He sent over the GETRAG casting number.

I ordered what I believed would be the correct flywheel, but it was delayed in transit and then held up by customs. On October 1 I finally received confirmation it had been released. During all that waiting, the car couldn't just occupy the entire shop indefinitely. Atan and I agreed that reinstalling the gearbox temporarily would let the other mechanical work continue.

Original blue aftermarket clutch pressure plate shown at workshop in Bohol
BUILD LOG // October 3 — Atan sent a photo of the bright blue clutch pressure-plate assembly and wrote: “Not fit boss.” Another fitment setback even after the parts search.

OCTOBER 3 / ATAN'S WORKSHOP UPDATE
Atan: “Not fit boss.” I asked for the car's exact year and more information because I was trying to identify the right clutch and flywheel combination. I decided to arrange a return/refund and consider a complete matched clutch-and-flywheel kit rather than gamble on more individual components.

I didn't want to start drilling the flywheel just to make the clutch fit. I'd rather find a matched clutch-and-flywheel setup that works properly, especially with the naturally aspirated stroker I have planned later. For now, the clutch upgrade was still on hold.

06 / October 15: belts, fan clearance and a few more surprises

By mid-October we were back to the cooling and accessories. Atan identified an air-conditioning compressor belt that needed replacement. One of my ordered drive belts was correct, but the other belt wasn't the proper fit. This isn't glamorous content, but it is the kind of troubleshooting that actually fills an old-car build.

Original used accessory belt marked 5PK890 held by the mechanic beside removed transmission
BUILD LOG // October 15 — Atan: “Need to replace aircon compressor belt.” He sent the belt marking, 5PK890, so I could help track down the correct replacement.
Original Gates Micro-V 5PK890 replacement accessory belt box
BUILD LOG // October 15 — Gates Micro-V 5PK890. This was the belt specification we were trying to match.

OCTOBER 15 / ATAN'S WORKSHOP UPDATE
Atan: “Drive belt you order is correct but theres spare belt also you ordered not the right.” He was checking local suppliers for the correct A/C belt to keep the job moving.

The electric radiator fan was also too close to the water-pump area. Atan sent a photo of the tight clearance and said the radiator fan needed adjusting. By my latest update, he'd made changes and managed to get it fitting, but the car still needs the remaining cooling-system work and a proper operational check.

Original tight clearance photograph between BMW E36 radiator electric fan motor and water pump pulley
BUILD LOG // October 15 — Atan: “Need to adjust the rad fan boss thers no enough clearcnce fan motor to water pump.” He later made the adjustment and got the fan to fit.

07 / October 16: service items, rear rods and stance

The next day Atan sent another piece of the puzzle: the used oil-filter element was ready for replacement. He looked around Tagbilaran for the correct part, even checking several auto-parts stores, but couldn't locate one at that time. We agreed to keep looking and order it online if necessary.

Original used BMW M50 cartridge oil filter standing on a metal work surface
BUILD LOG // October 16 — Atan: “This is the oil filter boss already needs to change.” He searched around Tagbilaran but couldn't find one locally.

OCTOBER 16 / ATAN'S WORKSHOP UPDATE
Atan told me he tried seven auto-parts shops in Tagbilaran and couldn't find the filter. In the same period, he was working through the rear control rods and stance while we continued discussing the cooling fan.

Original full front view of silver BMW E36 325i outside Bohol workshop
BUILD LOG // October 16 — Atan sent me another look at the E36 after the suspension adjustments. I was excited to see how it was sitting.
Original side profile silver E36 with five-spoke wheels and fresh lowered stance
BUILD LOG // October 16 — Another angle of the new stance. The real test will be how it feels once I get it back on the roads in Bohol.

I couldn't wait to find out how it handled and whether the shaking I'd noticed before was gone. But Atan couldn't get it started that day. He first wondered if it was out of fuel, then said he'd check the fuel pump. I knew there was fuel in it before, so we still needed to figure out what was happening.

08 / Where the car stands now — November 2026

This is still a working project. Atan has adjusted the radiator-fan fitment, but the wiring remains the headache. He is sorting the headlight and fog-light wiring, keeping the underglow on its own switch and dealing with the A/C being on a separate switch because of what a previous owner did. The front lip pieces are being removed so stronger, more durable replacements can go on. More pictures are coming when I'm back in Bohol.

The car is not getting a fabricated finished-car reveal in this article. I have a separate visual goal for the styling: eventually a distinctive, beautifully finished E36 with FSE character. That's the destination, not what the car looks like today. The photos above show the real stages and the actual people and parts involved.

Future design concept for the FSE E36 with silver body, blue and purple graphics, rooftop cargo box and blue underglow
FINAL VISION / CONCEPT RENDER // The look I'm working toward: silver, blue and purple FSE graphics, aggressive aero, and that blue underglow. Still a concept, but this is the vision.

Once the current repairs are properly checked, the next phase is a proper drive to see how the suspension feels on Bohol roads, checking for rubbing, vibrations, cooling behavior and drivability. Then we can revisit the engine: a naturally aspirated 3.0-liter stroker concept, with the details planned after the car has proved its foundation. This build is about feeling good on the road and loving the car, not chasing a made-up dyno number or pretending it is a drift missile.

09 / Why I'm documenting the whole journey

It's easy to post a shiny car and say it was built. What people don't see is the wrong part delivered from overseas, the mechanic sending a photo and saying it doesn't fit, the weeks spent waiting on a flywheel, or running around town looking for a belt or filter. That's the actual experience of trying to build an older BMW in the Philippines while working overseas. There are wins, setbacks, real conversations and real problem-solving.

I love seeing the updates coming in from Atan, even when the news isn't what I wanted to hear. Every problem we sort out gets this old BMW one step closer to the car I have in mind. And when I get back to Bohol, I want to see all of this progress for myself.

There's still wiring to sort out, the underglow needs its own switch, and the front lip is getting replaced. After that, I want to get behind the wheel, see how it feels on the roads here, and figure out what needs attention next. I'll share more photos when I'm back at the shop.

One day this E36 will have the look, the sound, and the naturally aspirated power I want. Right now we're building toward it, one repair at a time.

FSE Garage · Bulletin Board · More FSE Stories

← More FSE Stories
MORE FROM FRONT SEAT EXTREME

Enjoyed this story?
Keep exploring.

More real builds, track days, and stories from the people behind them.

Browse all stories